Mg gas infiltration for the fabrication of MgB2 pellets using nanosized and microsized B powders

MgB₂ superconductor pellets were synthesized through Mg gas infiltration method using nanosized- and microsized B powders. There was a marked difference in the superconducting properties of the two samples, particularly in the pinning force and dominant pinning mechanism. The microstructures of the samples were observed using HR-TEM and STEM-HAADF, and the results showed that the primary reason for the difference in the superconducting properties is the distribution of the nanosized second-phase particle MgO. Additionally, a feasible reaction model for the Mg gas infiltration method was established. Compared to the Mg liquid infiltration method, the gas infiltration showed better penetrability ability with a small amount of residual Mg. This study presents a novel synthesis process to fabricate an MgB₂ pellet with superior density and superconducting properties. This method can be used in multiple applications such as superconducting bearings, compact superconductor magnets, and magnetic shielding.     

超厚板TC4钛合金电子束焊接接头应力腐蚀敏感性

针对100 mm超厚板TC4钛合金电子束焊接接头，采用慢应变速率拉伸方法评价接头在人造海水中的应力腐蚀敏感性，分析接头的显微组织和断口形貌，对接头的腐蚀机制进行研究. 结果表明，室温条件下应变速率为ε=1×10-6 s-1时，母材在海水中未表现出应力腐蚀敏感性；焊缝上部、中部和下部具有轻微应力腐蚀敏感性. 焊缝在海水中发生阳极溶解，产生氢吸附，导致裂纹的萌生. 同时氢扩散诱导α'相界及α'相内发生位错塞积，进而使裂纹在更低的应力水平下发生扩展.     

Approaching Ultrastable High‐Rate Li–S Batteries through Hierarchically Porous Titanium Nitride Synthesized by Multiscale Phase Separation

Porous architectures are important in determining the performance of lithium–sulfur batteries (LSBs). Among them, multiscale porous architecutures are highly desired to tackle the limitations of single‐sized porous architectures, and to combine the advantages of different pore scales. Although a few carbonaceous materials with multiscale porosity are employed in LSBs, their nonpolar surface properties cause the severe dissolution of lithium polysulfides (LiPSs). In this context, multiscale porous structure design of noncarbonaceous materials is highly required, but has not been exploited in LSBs yet because of the absence of a facile method to control the multiscale porous inorganic materials. Here, a hierarchically porous titanium nitride (h‐TiN) is reported as a multifunctional sulfur host, integrating the advantages of multiscale porous architectures with intrinsic surface properties of TiN to achieve high‐rate and long‐life LSBs. The macropores accommodate the high amount of sulfur, facilitate the electrolyte penetration and transportation of Li⁺ ions, while the mesopores effectively prevent the LiPS dissolution. TiN strongly adsorbs LiPS, mitigates the shuttle effect, and promotes the redox kinetics. Therefore, h‐TiN/S shows a reversible capacity of 557 mA h g^?1 even after 1000 cycles at 5 C rate with only 0.016% of capacity decay per cycle.     

Ti-xCr-yCu钛基材料的制备及组织性能研究

通过粉末冶金法制备了Ti-xCr、Ti-yCu及Ti-xCr-yCu钛基材料,研究了Cr、Cu含量对其相组成、显微组织、压缩屈服强度、弹性模量以及切削加工性能的影响规律。结果表明:随Cr含量的增加,Ti-xCr钛基材料依次出现了Ti_4Cr、TiCr_2及Cr相,其压缩屈服强度表现出先增大后减小的趋势,当Cr含量为10%时其屈服强度达到最大值(710 MPa),同时,添加Cr元素有利于降低钛基材料的弹性模量,最低可达25 GPa。添加Cu元素的钛基材料,随Cu含量的增加,Ti_2Cu相增加,并且显微组织细化,屈服强度降低;弹性模量受Cu含量影响较小而受烧结温度影响较大。添加Cr和Cu元素的钛基材料,其显微组织主要为网篮组织,弹性模量低于纯钛,其中添加Cu元素有利于细化层片,添加Cr元素有利于细化等轴组织。此外,Cr含量为5%时,钛基材料具有较佳的切削加工性能。     

两种3D打印用雾化Ti-6Al-4V粉末的对比研究

本研究分别利用水冷铜坩埚真空感应熔炼气雾化(VIGA-CC)和等离子旋转电极(PREP)两种技术制备出球形Ti-6Al-4V合金粉末,作者利用SEM、同步辐射CT扫描-三维重建和氩气含量测试等分析手段对不同粒径的Ti-6Al-4V合金粉末的孔洞缺陷和氩气含量、硬度值进行了表征。实验结果表明, VIGA-CC粉末粒度分布宽,细粉收得率较多,粉末粒度分布在40~180 μm之间, PREP粉末的粒度分布较窄,主要集中在110~180 μm之间；金属粉末内部的孔隙率、气体含量和孔尺寸随着粉末粒度的增大而增大,且同一粒径范围内VIGA-CC粉末的气孔概率多于PREP粉末；随着粉末粒径减小,粉末截面组织逐渐细化,其硬度值逐渐升高,整体上VIGA-CC粉末硬度值高于PREP粉末。     

Oxidation‐led decomposition of hexagonal boron nitride coatings on alloy substrates at 900 °C: Ti‐6Al‐4V

Hexagonal boron nitride (h‐BN) coatings on Ti‐6Al‐4V substrates undergo complete decomposition in air at 900 °C. This fate is similar to that of this ceramic material on chromia‐former alloys, and unlike that of a mass of powder treated in isolation. As the ceramic and alloy oxidize concurrently, outwardly diffusing aluminum (III) ions but not the predominant titanium (IV) ions react with the boron trioxide that forms around the h‐BN basal plane peripheries. Resultant aluminum borate is incorporated into the growing scale and the boron trioxide diffusion barrier is depleted. By this mechanism, the oxidation of h‐BN is maintained at an enhanced rate, until both this material and its oxide completely decompose. Liberated nitrogen from the oxidation of h‐BN can enter the underlying scale as a randomly distributed solute in rutile solid solution. The post‐coating oxide‐atmosphere interface comprises elongated aluminum borate crystallites protruding through at the boundaries between 3–5 at% nitrogen‐doped rutile grains. It differs significantly from that of oxidized, uncoated Ti‐6Al‐4V, which is occupied by a thin α‐alumina layer atop rutile. This interface does not change with an additional 72 h of heat‐treatment.     

The isothermal reduction kinetics of chromium-bearing vanadium–titanium magnetite sinter

The reduction of chromium-bearing vanadium–titanium magnetite sinter (CVTMS) by CO was investigated at 1123–1223?K. The reduction degree increased with increasing temperature. The isothermal reduction kinetics of CVTMS was analysed, according to Sharp analysis and ln–ln analysis, the kinetic mechanism of reduction process for all samples in different basicity can be represented as f(α)?=?1.61(1?α)[?ln(1?α)]^1–1/1.61. The reaction activation energy of all samples (R?=?1.9, 2.1, 2.3, obtained according to the components of the materials burdening used in sintering process) at different reaction degrees were calculated by the model-free method. And the pre-exponential factors of reaction also were calculated by the mathematical method. The rate controlling step for the reduction process under the present reduction condition was chemical reaction.     

脱硫胶粉在乳化改性沥青中的应用

考察了不同规格胶粉及不同脱硫程度的脱硫胶粉对橡胶改性乳化沥青性能的影响,结果表明,采用100目胶粉即可制备出橡胶改性乳化沥青,但乳化沥青的性能较差;采用活化度为50%左右的100目脱硫胶粉制备乳化沥青时,脱硫胶粉的用量相比于胶粉可大幅提高;在通过外掺100目50%左右活化度的脱硫胶粉(质量分数15%,以沥青计,下同)和质量分数2%的苯乙烯-丁二烯-苯乙烯嵌段共聚物改性的乳化沥青中添加质量分数1%的丁苯胶乳,所制备橡胶改性乳化沥青无筛上剩余物,5 d储存稳定性为2.9%,蒸发残留物的25℃针入度、软化点和5℃延度分别为55 (0.1 mm)、64.5℃和22.5 cm,能够满足乳化改性沥青的技术指标要求。